20 Best PCB Making techniques

Hello all Ingeniumblog is back with more stuff. Here you will find a huge, comprehensive and carefully picked Roundup on PCB making. Have FUN!!!

(Mostly) easy PCB manufacture

This is an easy way to create your own PCBs at home. The method is based on the “5 Bears ” process (which is itself based on Tom Gootee’s process).

Design a PCB using a etch marker and ferric chloride

Article by cliffyd.

An article by psychogenic. Using PCBs can even help reduce the time you spend building circuits, especially if you are producing multiple units, as you only need to follow a parts placement diagram . As is usually the case, there is more than one way to do it: there are numerous ways to create PCBs. They range from the time-consumming and difficult to the fully automated and expensive. Here we will attempt to describe a method we’ve found ideal for small production runs of single- or double-sided boards.

Making a Hand Drawn PCB

Ohm has decided to make a hand drawn PCB for his resistor substitution box.This process works well for simple circuits that do not have a lot of small parallel bus lines in them.

How to make a PCB

This project will explain how you make your own PCB. You will be amazed how easy it is and how good the result will be. All you need is so get some basic stuff and time for experimenting.

How to Make PCB’s

One of the most discouraging things about making a hardware project (apart from obtaining all of the components) is building the printed circuit board – PCB. It is sometimes possible to use strip board or some other pre-fabricated board but more often than not the circuit complexity and performance requires a proper PCB to be made. The good news is that due to improvements in printing and processing technologies it is now relatively easy to make inexpensive high quality PCB’s at home.

PCB – Copper Printed Circuit Boards

A great article on PCB making by David Cook. Solderless breadboards are the fastest and most flexible way to design and experiment. When the circuit is ready for more permanent use, there are several methods of connecting components together that are appropriate for one-time designs in robots. Point-to-point soldering can result in a rat’s nest problem. Homemade printed circuit boards are a good solution.

How to make PCBs at home in 1 hour

If you take your electronics hobby seriously, you already feel the need for a simple and fast technique for making your own printed-circuit boards (PCB). Here Alberto is going to show how to make simple single-sided PCBs in a snap, using widely available materials. This technique works reliably for thin tracks down to 10 mils, and is suitable for most surface-mount parts.

DIY Flexible Printed Circuits

Produce your own single-sided flexible printed circuits using a solid ink printer, copper-coated polyimide film, and common circuit board etching chemicals. You will find flex PCBs inside most cellphones or similar miniaturized gadgets. Flex PCBs are useful for making tiny cables and extremely lightweight circuits. Article by ckharnett.

Printed Circuit Boards (PCB) using the Laser Cutter

This is a new twist on an existing process by mashorter, which allows you to make super accurate PCBs. It basically involves spray painting copper board, laser cutting off the paint and then putting the board in a bath of Ferric Chloride to remove the unwanted copper. This method is particularly good when using large chips as they need very accurate pin spacing.

Custom PCB Prototyping using a Laser Cutter

jmsaavedra is going to walk you through the process of prototyping a Printed Circuit Board using a laser cutter and supplies from your local Radioshack and hardware store.

How to make really really good homemade PCBs

This page [by Mike] is a guide to producing consistently high quality PCBs quickly and efficiently, particularly for professional prototyping of production boards. Unlike most other PCB homebrew guides, emphasis is placed on quality, speed and repeatability rather than minimum materials cost, although the time saved by getting good PCBs every time usually saves money in the long run – even for the hobbyist, the cost of ruined PCB laminates can soon mount up!

5V breadboard mini PSU

A simple tutorial on making a 5V power supply unit by chr at instructables.

You can Connect to 9V battery, 12V or any other DC power source from 8 to 18 volts.

Cheap and Easy Toner Transfer for PCB Making

There are lots of people mentioned about using Inkjet Glossy Paper to do Toner Transfer. It can be done. But it is not easy to remove it after ironing. You have soak the PCB in hot water for more than ten minutes. It is quite time consuming. If you cannot remove the coating completely. It cannot be etched. article by hilarycheng

Sponge + Ferric Chloride Method — Etch PCBs in One Minute!

In this Instructable, TechShopJim will show you how to etch a circuit board with about a tablespoon of ferric chloride etching solution and a 2 inch square sponge. You will be amazed as the exposed copper on the PCB disappears before your eyes, and your board is completely etched in a minute or less!

Two sided PCB using toner method

This tutorial by jmengel describes an easy method to make professional looking two-sided printed circuit boards at home.

That’s all for this moment!

Wait till the next episode for more updates…

Thanks for following this Roundup. I hope you got a good idea on Making your own Power Supply Unit(PSU).. Your feedback helps us improve, and we always look forward to learning which features you like and enjoy. Send us comments

Making your own PCB’s at Home